More Views

YS-37 XL6009 4A boost module with display 400K



Quick Overview

Seller Name : Mod N Shields
Best Quality Wholesale Price
Cash-On-Delivery: Not Available for this product



Product Details

XL6009400KHz4ASwitching current boost module


Module performance and features:

XTW6009Is a 4A High-performance boost switch current? BOOST ?Module. The module uses the second generation of high-frequency switching technology XL6009E1 Core chip performance than first-generation technology LM2577 . XL6009 Boost module at a lower cost, superior performance, LM2577 Module is about to be eliminated.

  •  Wide input voltage 3V ~ 32V ?5V The following step-up work, but digital does not work? Optimum operating voltage range5 ~ 32V ;
  •  Wide Boost The output voltage5V ~ 35V ;
  •  Internal 4A Efficient MOSFET Switch, so that the maximum efficiency of 94% ;? LM2577 Current only 3A ?
  •  Ultra-high switching frequency 400KHz , You can use a small-capacity filter capacitor that is able to achieve very good results, the ripple is smaller and smaller.? LM2577 Frequency Only 50KHz ?
  •  With power indicator light
  •  With a voltage meter and voltmeter can display self-calibration. It uses a more advanced micro cessor voltage, voltage meter error 0.05V , Range 0 ~ 35 V .?Note: To ensure the accuracy of the voltmeter, please ensure that the input voltage 4.5V the above?
  •  Touch the button to switch measuring input or output voltage, and has a light show which is being measured voltages, and save the settings, even if the power is turned on again.
  •  Voltmeter can be turned off, when not to be displayed on the left touch button can be easily achieved.
  •  Band terminals, no iron can also be easy to use, and retention wire connection points.
  •  Overheating tection and short circuit tection
  •  size 6 0 * 3 5 *1 3.5 mm
  •  weight twenty four g

Technical Parameters:


The modular nature of : Non-isolated boost?BOOST ?

Rectification : Non-synchronous rectification

Input Current : 4A?maximum?, Load 18mA ? 5V enter, 8V Output load less than 18mA . The higher the voltage, load current increases.?

Conversion efficiency : 94%?The greater the pressure, the lower the efficiency?

Switching Frequency : 400KHz

Output ripple : 50mV?The higher the voltage, the greater the current, the greater the ripple?

Load Regulation : 0.5%

Voltage Regulation : 0.5%

Operating temperature : -40? ~ + 85 ?

Dimensions : 43mm * 21mm * 14mm?long * width * high?

IN + : Input +


IN- : The negative input

OUT + : Output +

OUT- : Output negative

Comparison Test Sample Reference:


enter 5V 12V0.8A9.6W


enter 7.4V 12V1.5A18W

enter 12V 15V2A30W

enter 12V 16V2A32W

enter 12V 18V1.6A28.8W

enter 12V 19V1.5A28.5W

enter 12V 24V1A24W

enter3V 12V0.4A4.8W

Onboard voltage meter self-calibration method:


1. When the board voltmeter shows the output voltage, long press on the right button 2 Seconds after the release, voltmeter and an output voltage indicator OUT Synchronous flashing, this time into the output voltage adjustment mode; Similarly, when the input voltage voltmeter display, press the button on the right side 2 Seconds after the release, voltmeter and input voltage indicator IN Synchronous flashing, this time into the input voltage adjustment mode;

2. Touch the button on the right side, the voltage increases a unit, touch the button on the left side, a voltage reduction unit; since the voltage value of less than one unit 0.1V , So you need to continuously press 1-5 Times to see changes in the voltmeter 0.1V Specific continuous button several times depending on the voltage value currently displayed, the current display higher the voltage, the less the number of press;

3. After the voltage is adjusted, press the button on the right side 2 Seconds after the release, this time to exit voltage calibration mode, all parameters set to automatically power-down save.

NOTE: You only need to adjust the way this one can obtain accurate calibration voltage value across the entire voltage range, this function is more accurate to meet your requirements and design, ease of use.


This module can be used in the output voltage is higher than the output voltage of boosting the input field, such as batteries, power transformer, DIY Adjustable power supply, 24V Car T of this power, industrial equipment buck, 9 turn 12 V , 12V turn 18 V , 18 V turn twenty four V Wait.


Related Images

Additional Information

SKU CC1212125303
Cash on Delivery No

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Don't Miss Out

Stay up-to-date with the latest news, hottest trends and new arrivals direct to your inbox

//inkocean pagelog